Online protractor
Put the corner you're measuring on the centre point and drag the two arms along its edges. The angle between them is shown to a tenth of a degree.
Tap near an arm to swing it there. With the keyboard, Tab to an arm and use the arrow keys: one degree at a time, a tenth with Shift, ten with Page Up and Page Down.
How to measure an angle
- Place the object flat on the screen with the corner of the angle on the red centre point.
- Drag the yellow arm so it runs along one edge of the angle, then drag the black arm along the other edge.
- Read the angle between the arms at the top. The reflex angle, the one measured the long way round, is shown underneath it.
Advertisement
No calibration needed
An angle stays the same however large it's drawn, so the protractor reads correctly on any screen and at any zoom level without calibrating first. Only lengths, such as those on the ruler and the ring sizer, depend on knowing the size of your screen.
Reading the scale
The scale runs from 0 to 360 degrees anticlockwise, starting at the right, like a full-circle protractor. An angle smaller than 90 degrees is acute, exactly 90 degrees is a right angle, between 90 and 180 degrees is obtuse, and anything over 180 degrees is reflex. A straight line is 180 degrees.
For the best result, make the arms as long as the edges allow and look straight down at the screen, not from the side. Short edges are harder to line up, so a small error in where you place an arm becomes a bigger error in degrees.
How accurate a reading is
The readout gives a tenth of a degree, but what limits a reading is how well the arms sit along the edges. An arm end that is 1 mm off the edge 50 mm from the corner is out by 1.1°; at 100 mm it is out by 0.6°, and at 150 mm by 0.4°. So lay the object on the largest screen you have, and drag each arm out to the far end of its edge before reading.
Mitre angles and roof pitch
Two of the commonest uses have angles you can work out in advance. A frame with equal sides closes when each joint is cut at 180° divided by the number of sides, so a picture frame takes four 45° mitres and a hexagon six 30° ones. A roof's pitch is its rise for every 12 of run; the angle is the arctangent of rise over 12, so a 6-in-12 roof is 26.6°. Both are in the tables below: check a cut piece or a rafter template against them on the protractor.
| Frame | Sides | Mitre at each end | Corner angle |
|---|---|---|---|
| Triangle | 3 | 60° | 60° |
| Square or rectangle | 4 | 45° | 90° |
| Pentagon | 5 | 36° | 108° |
| Hexagon | 6 | 30° | 120° |
| Octagon | 8 | 22.5° | 135° |
| Twelve-sided | 12 | 15° | 150° |
| Roof pitch | Angle | Percent |
|---|---|---|
| 1 in 12 | 4.8° | 8% |
| 2 in 12 | 9.5° | 17% |
| 3 in 12 | 14.0° | 25% |
| 4 in 12 | 18.4° | 33% |
| 5 in 12 | 22.6° | 42% |
| 6 in 12 | 26.6° | 50% |
| 7 in 12 | 30.3° | 58% |
| 8 in 12 | 33.7° | 67% |
| 9 in 12 | 36.9° | 75% |
| 10 in 12 | 39.8° | 83% |
| 11 in 12 | 42.5° | 92% |
| 12 in 12 | 45.0° | 100% |
More measuring tools
Advertisement
Advertisement
Advertisement